Friday, March 30, 2012

Bed Coverings

As bunks in boats never seem to be a "normal shape" the sheets and covers for the bunks typically need to be tailor made to suite.

This is especially true for a V-berth, as there is nowhere for the massive amount of excess sheet, blanket, or comforter to sit. Having it all piled up on your feet is uncomfortable.  Solution: custom make the sheets and comforter.

As the V-berth was going to be my daughter's bunk, she had a vested interest in making sure that it was comfortable.  Sarah was also keen to use her sewing skills with a sewing machine, so we set about making the custom comforter for the forward V-berth.
Sarah had already picked out the colour scheme for the interior of the boat. It was to be bright and happy. Her colour picks were for the settee cushions to be a mid blue, while scatter cushions, and bedding to be a bright gold colour.

Using a paper pattern of the V-berth, it was possible to mark out, and cut down to shape what would be the middle of the comforter.  We started with a medium weight synthetic comforter for a double bed from IKEA, and decided to make the comforter 250mm wider on each side than the mattress. The V-berth on Moor or Less is actually not a normal V shape, at the head end, it has two parallel sides before beginning to tapper. The shape of the comforter will also have to follow this shape.

The cut or raw edges of the comforter were then sewn and a hem put on it. It was now time to make the cover using the gold material which Sarah had picked out.

The material wasn't wide enough to cover the cut down comforter. Pieces of material had to be added to both sides to obtain the width.

Once the cover had been sewn together and the comforter placed inside, job successfully completed. Sarah was then eager to try out the comforter, but that will have to wait. Need to make the fitted, and flat sheets for the V-berth next.

The finished V-berth comforter
Since we now have the shape of the aft cabin bunk, the comforter and sheets for that bunk can be made.

Changing the Aft Cabin Layout

The aft cabin of Moor or Less is not large and could best be described as "cossie".  The original setup for the aft cabin had a rather unusual layout. Basically there was a "U" shaped bunk which allowed you to have two single bunks, one on either side, or a very narrow double bunk across the aft of the cabin.

Neither of these two bunk configurations appealed to me, so an alternate configuration was sort.

I decided that a double bunk running fore/aft was more suitable, however in order to have room to sit up in bead, the head of the bed would have to be forward, and the foot aft. This is less than desirable setup when sailing (head must always be aft), but upon thinking about it, the aft cabin would not be used during over night passage making anyway.  The port saloon berth was the most suitable sea berth.

To make the double berth, much of the fiddle which had been put in place would need to be removed (and re-used later), and a platform built over what was previously standing area below the aft cabin hatch. Under the platform would be turned into the new storage area.

First step was to determine the actual bunk size. The bunk was not going to be a rectangle shape due to the curvature of the hull. The foot of one side would need to be cut away following the side of the hull. The head of the bunk is the standard width for a double bed, 1400mm, but was slightly shorter than a normal double bed at only 1770mm (normally 1830mm)

Making the Mattress
As the berth would hopefully be used for many nights, I wanted a firm mattress. It was off to Clarke Rubber who had a double mattress of medium density foam, which I tested on the shop floor, it felt perfect. Though the medium density foam is more expensive than the regular low density, the extra comfort will be worth the dollars.

Once back home, the job of cutting the mattress to size began. Having learnt the trick of cutting foam many years ago, this wasn't too much of a challenge. First step as the place the paper pattern on top of the foam, and tracing out the shape with a marking pen.


Marked out ready for cutting

Next part is the "trick" cut along the pen line using an electric carving knife. The electric knife cuts the foam effortlessly, and gives a smooth straight finish.

The mattress came with a lightweight material cover, and while it is not high quality material, it will suffice as the initial cover. Using the paper pattern again, the shape was traced out, and material cut. A quick run along the cut edge with the sewing machine completed the cover.

Moving the Battery Switch
The platform which forms the top of the new storage enclosure needed to be built, however first, the original battery switch and power distribution point had to be moved. Part of the new compartment would be allocated for this purpose, with the new Battery switch mounted on the side of the compartment.

Moving the electrical panel to the side of the new storage switch involved the removing of the old setup, building the new storage compartment,  then rebuilding the electrical panel. The original battery switch, while certainly capable of carrying large amount of current, required a spanner to operate, and couldn’t be done quickly. A more conventional setup was preferred using a rotary switch for two battery banks. As the new location of the electrical switch and junction was adjacent to the existing, the cabling just needed to be redirected slightly after removing the old electrical box.

Making the Bunk Base
The bulk of the bunk base is formed with the original "U" shaped structure. 

The exiting timber fiddles required removal, and they were not going to come off easy. The fiddles had been glued and screwed into place, with the screws then covered over with bungs.
To remove with minimum effort and time, an electric coping saw was used. The piece of the fiddle which protruded above the height of the bunk base, I planned to re-use, so wanted them removed undamaged.

In order to support the top of the new storage compartment, some timber frames were fixed onto the exiting bunk base with screws and Epoxy, 12mm below the height of the bunk based so that the plywood lid would be flush.

Thursday, March 29, 2012

Somewhere for Coffee Cup

On those cold mornings when you want to lay in bed and enjoy reading a book, with a hot cup of tea or coffee at hand while the wind and rain attack those who venture outside, a place is needed to rest the coffee cup.

This coffee stand needed to be within easy reach. The aft berth on Moor or Less will have the head of the berth forward (not planned to be used while sailing), the area next to the pillow, against the hull seemed like a good location for a small (very small) bedside table.

To make the top of the bedside cabinet a small piece of cabin sole ply with the teak and ask striped paneling has been used. Around the top of the table surface, a small fiddle is installed to stop items sliding off should there be a rolling anchorage. Access to the small cabinet below is through the hinged table top which tilts up, pivoting from the hull side of the hull.

I wanted the lid of the storage compartment to be slightly higher than the mattress of the bunk. Similar compartments were also needed on either side of the V-berth.

Measuring Up
Starting with the aft cabin, and Using a piece of cardboard for a template, the shape of the hull was traced and cut out.

The hull is moving outwards as you move forward, and not paralell to the berth. The top of he compartment will be in two parts and consist of a lifting rectangle piece hinged off a tappered piece which is attached to the hull.Using small stainless steel butt hinges to joing the two pieces of the compartment top, it will be neccessary to joint them by the hinges prior to attaching the fixed piece to the cabinet.

Installation
With the hull as one side of the cabinet, the bulkhead as another, and the bunk base as the bottom, leaving only two sides and the top to be created.. The two sides of the cabinet are made from maple 90mm x 12mm, and are sealed using interior vanish, as is the cabinet top.To attach the cabinet to the hull and bulkhead, small timber battens needed to be attached with Epoxy. The sides of the cabinets will be screwed onto these timber battens allowing it to be removed easily if required in the future.

Obtaining the profile of the vertical curve on the hull where the cabinet side attached to the hull was obtained by placing the partially constructed cabinet on the bunk next to where it is to be installed, and the profile "fished" onto the side of the cabinet. Once the profile has been cutout on the side of the cabinet, the locations of the battens could be marked and glued in place.Once the Epoxy had set, the cabinet was attached with s/s screws, and the inside of the cabinet lined with the synthetic felt. Contact Adhesive was used to bond the lining to the cabinet.